How to Remove a Magpul Stock from an AR-15
How to Remove a Magpul Stock from an AR-15
The Magpul MOE stock is a popular choice for AR-15 owners because of its lightweight design and comfortable feel. However, it can be difficult to remove if you don’t know what you’re doing. In this article, we’ll walk you through the process of removing a Magpul stock from an AR-15 in a few simple steps.
Step 1: Disassemble the AR-15
The first step is to disassemble the AR-15 so that you can access the stock. To do this, follow these steps:
1. Remove the magazine from the rifle.
2. Lock the bolt back.
3. Rotate the rear takedown pin 90 degrees and remove it.
4. Push the front takedown pin out and remove the upper receiver from the lower receiver.
Step 2: Remove the Stock Screws
Now that the AR-15 is disassembled, you can remove the stock screws. The stock screws are located on the bottom of the stock, near the rear of the receiver. Use a Phillips head screwdriver to loosen and remove the two stock screws.
Step 3: Remove the Stock
With the stock screws removed, you can now remove the stock from the AR-15. Simply lift up on the stock and pull it away from the receiver.
Step 4: Reassemble the AR-15
To reassemble the AR-15, simply reverse the steps you took to disassemble it. First, install the stock on the receiver, then insert the upper receiver into the lower receiver. Finally, replace the takedown pins and lock the bolt back.
Now that you know how to remove a Magpul stock from an AR-15, you can easily customize your rifle with a new stock or other accessories.
| Step | Instructions | Image |
|---|---|---|
| 1 | Ensure the AR-15 is unloaded and safe to work on. |  |
| 2 | Locate the two hex screws on the back of the stock. |  |
| 3 | Use a hex wrench to loosen the screws. |  |
| 4 | Pull the stock back and off of the AR-15. |  |
The Magpul MOE stock is a popular choice for AR-15 rifles, as it offers a comfortable and customizable fit. However, if you need to remove the stock for cleaning or maintenance, it’s important to know how to do it properly. In this guide, we will walk you through the steps of removing a Magpul MOE stock from an AR-15 rifle.
Tools and Materials
To remove a Magpul MOE stock from an AR-15 rifle, you will need the following tools and materials:
- AR-15 rifle
- Magpul stock
- AR-15 takedown/pivot pins
- AR-15 armorer’s wrench
- Small screwdriver
Steps
1. First, remove the AR-15’s handguard. To do this, you will need to use the AR-15 armorer’s wrench to loosen the two screws that secure the handguard to the barrel nut. Once the screws are loose, you can slide the handguard off of the barrel nut.
2. Next, you will need to remove the AR-15’s takedown/pivot pins. These pins are located at the rear of the receiver, and they secure the upper and lower receivers together. To remove the takedown/pivot pins, you will need to use the small screwdriver to pry them out of their respective holes.
3. Once the takedown/pivot pins are removed, you can separate the upper and lower receivers.
4. Now, you can remove the Magpul stock. To do this, you will need to press down on the two tabs on the back of the stock and slide it off of the receiver extension.
5. That’s it! You have now successfully removed the Magpul MOE stock from your AR-15 rifle.
Removing a Magpul MOE stock from an AR-15 rifle is a relatively simple process, but it is important to follow the steps carefully to avoid damaging your rifle. If you have any questions, please consult with a qualified gunsmith.
Here are some additional tips for removing a Magpul MOE stock from an AR-15 rifle:
- Make sure that the rifle is unloaded and safe to work on.
- Be careful not to drop any small parts.
- If you are having trouble removing the stock, you can use a small amount of lubricant to help loosen it.
- Once you have removed the stock, clean and inspect it for any damage.
- Replace the stock and reassemble the rifle.
3. Remove the AR-15’s rear takedown/pivot pin
The AR-15’s rear takedown/pivot pin is located at the back of the receiver, just above the buffer tube. It is a small, cylindrical pin that is held in place by a spring. To remove the rear takedown/pivot pin, you will need to use a small punch or awl.
1. Insert the punch or awl into the hole in the center of the pin.
2. Apply pressure to the punch or awl and push the pin out of the receiver.
3. The pin will come out with a spring.
Once the rear takedown/pivot pin is removed, the upper and lower receivers can be separated.
4. Remove the AR-15’s front takedown/pivot pin
The AR-15’s front takedown/pivot pin is located at the front of the receiver, just below the gas block. It is a small, cylindrical pin that is held in place by a spring. To remove the front takedown/pivot pin, you will need to use a small punch or awl.
1. Insert the punch or awl into the hole in the center of the pin.
2. Apply pressure to the punch or awl and push the pin out of the receiver.
3. The pin will come out with a spring.
Once the front takedown/pivot pin is removed, the upper and lower receivers can be separated.
In this tutorial, you learned how to remove the Magpul stock from an AR-15. By following these steps, you can easily remove the stock and access the internal components of your rifle.
How do I remove a Magpul stock from an AR-15?
1. Ensure that the rifle is unloaded and safe to work on.
2. Locate the two takedown pins on the rear of the receiver.
3. Depress the takedown pins and simultaneously rotate them out of their respective holes.
4. Carefully separate the upper and lower receivers.
5. Locate the castle nut and delta ring assembly at the rear of the receiver extension.
6. Use a Magpul AR-15 tool or a similar tool to loosen the castle nut.
7. Remove the castle nut and delta ring assembly.
8. Grasp the stock and pull it straight back off of the receiver extension.
What tools do I need to remove a Magpul stock from an AR-15?
You will need the following tools to remove a Magpul stock from an AR-15:
- A Magpul AR-15 tool or a similar tool to loosen the castle nut
- A flathead screwdriver
Can I remove a Magpul stock without tools?
It is possible to remove a Magpul stock without tools, but it is not recommended. Using tools will make the process much easier and less likely to damage the stock or the rifle.
What if I can’t find the takedown pins?
The takedown pins are located on the rear of the receiver, just above the magazine well. They are small, round, and have a flat head. If you are having trouble finding them, you can use a flashlight to help you see them.
What if I can’t loosen the castle nut?
If you can’t loosen the castle nut, you can use a Magpul AR-15 tool or a similar tool to help you. The tool will fit into the castle nut and provide you with more leverage to turn it.
What if I can’t remove the delta ring assembly?
The delta ring assembly can be difficult to remove, especially if it is tight. You can use a flathead screwdriver to help you pry it off. Be careful not to damage the delta ring assembly or the receiver extension.
What if I can’t remove the stock?
If you can’t remove the stock, you may need to use a different tool or technique. You can also try heating the stock up with a hair dryer or heat gun to make it more pliable. Be careful not to damage the stock or the rifle.
What are the benefits of removing a Magpul stock from an AR-15?
There are a few benefits to removing a Magpul stock from an AR-15, including:
- Access to the buffer tube: Removing the stock will give you access to the buffer tube, which is used to connect the stock to the rifle. This can be useful for cleaning or replacing the buffer tube.
- Adjustability: Some stocks are more adjustable than others. If you remove the stock, you may be able to adjust it to a different length or position. This can make the rifle more comfortable to shoot.
- Customization: Removing the stock allows you to customize the rifle with a different stock. This can change the look, feel, and performance of the rifle.
What are the risks of removing a Magpul stock from an AR-15?
There are a few risks associated with removing a Magpul stock from an AR-15, including:
- Damage to the rifle: If you are not careful, you could damage the rifle while removing the stock. This could include scratching the finish or damaging the internal components.
- Injury: If you are not careful, you could injure yourself while removing the stock. This could include cutting yourself on the sharp edges of the stock or the rifle.
- Loss of functionality: If you remove the stock, you could lose some of the functionality of the rifle. This could include the ability to adjust the stock or the ability to use the rifle with a sling.
In this tutorial, we have shown you how to remove a Magpul stock from an AR-15. We hope that you found this information helpful. If you have any questions, please feel free to leave them in the comments section below.
Here are the key takeaways from this tutorial:
- To remove a Magpul stock from an AR-15, you will need a hex key and a punch.
- The hex key is used to loosen the castle nut, which holds the stock in place.
- The punch is used to drive out the roll pin that secures the stock to the receiver.
- Once the castle nut and roll pin are removed, the stock can be easily removed from the rifle.
We hope that this tutorial has been helpful. If you have any questions, please feel free to leave them in the comments section below.