How To Remove A Bolt From A Remington 700?

The Remington 700 is a popular bolt-action rifle that is used for hunting, target shooting, and other shooting sports. One of the most basic tasks that you will need to know how to do is how to remove the bolt from the rifle. This is a relatively simple process, but it is important to do it correctly in order to avoid damaging the rifle.

In this article, we will walk you through the steps of removing the bolt from a Remington 700. We will also provide some tips on how to do it safely and efficiently. So, if you are new to owning a Remington 700, or if you simply need a refresher on how to remove the bolt, then read on!

Step	Instructions	Image
1	Depress the bolt release button and pull the bolt handle to the rear.
2	Rotate the bolt handle clockwise until it stops.
3	Grasp the bolt body and pull it straight out of the receiver.

Safety Precautions

When removing the bolt from a Remington 700, it is important to take the following safety precautions:

• Always keep the rifle pointed in a safe direction. This means downrange, away from people and animals.
• Make sure the rifle is unloaded. Check the chamber and magazine to ensure that there is no ammunition present.
• Remove the safety. This will allow you to operate the bolt more easily.
• Wear eye protection. This will protect your eyes from any debris that may be released when you remove the bolt.
• Use a vise or other secure workbench. This will help to prevent the rifle from slipping and causing injury.

Tools and Materials Needed

The following tools and materials are needed to remove the bolt from a Remington 700:

• A Remington 700 rifle
• A vise or other secure workbench
• A cleaning rod
• A bore brush
• A rag
• A small screwdriver
• Penetrating oil

Instructions

To remove the bolt from a Remington 700, follow these steps:

1. Place the rifle in a vise or other secure workbench.
2. Remove the bolt handle by turning it counterclockwise until it comes loose.
3. Use a cleaning rod to push the bolt out of the receiver.
4. Use a bore brush and a rag to clean the inside of the receiver.
5. Apply a small amount of penetrating oil to the bolt threads.
6. Reinsert the bolt into the receiver and turn the bolt handle clockwise until it is snug.

Removing the bolt from a Remington 700 is a relatively simple process, but it is important to take the necessary safety precautions to avoid injury. By following the steps outlined in this guide, you can safely remove the bolt from your rifle and perform necessary maintenance.

3. Steps in Removing the Bolt

To remove the bolt from a Remington 700, you will need the following tools:

• A 3/8-inch Allen wrench
• A 10mm socket wrench
• A flathead screwdriver

1. With the rifle unloaded and the safety engaged, remove the bolt handle by turning it counterclockwise until it comes loose.
2. Use the 3/8-inch Allen wrench to loosen the two bolts that hold the bolt sleeve in place.
3. Remove the bolt sleeve by pulling it straight up.
4. Use the 10mm socket wrench to loosen the two bolts that hold the bolt in place.
5. Remove the bolt by pulling it straight up.

Once the bolt is removed, you can clean and lubricate it as needed. Be sure to reassemble the bolt in the reverse order of disassembly.

4. Testing the Bolt for Proper Function

After you have reassembled the bolt, you should test it for proper function. To do this, follow these steps:

1. Load a dummy round into the rifle.
2. Engage the safety and pull the trigger.
3. The bolt should move forward and extract the dummy round.
4. Release the trigger and the bolt should move rearward and chamber a new round.
5. Repeat steps 2-4 to ensure that the bolt is functioning properly.

If the bolt is not functioning properly, you may need to take it to a gunsmith for repair.

Removing and replacing the bolt on a Remington 700 is a relatively simple task that can be accomplished with a few basic tools. By following the steps in this guide, you can safely and effectively remove and replace the bolt on your rifle.

How do I remove the bolt from a Remington 700?

1. Ensure that the rifle is unloaded and the safety is engaged.
2. Remove the magazine from the rifle.
3. Depress the bolt release button located on the left side of the receiver.
4. While depressing the bolt release button, pull the bolt handle to the rear and out of the rifle.

What if the bolt is stuck?

There are a few possible reasons why the bolt may be stuck.

• The bolt may be dirty or corroded.
• The bolt may be out of alignment with the receiver.
• The bolt may be seized due to rust or corrosion.

If the bolt is dirty or corroded, you can try cleaning it with a solvent and a brush. If the bolt is out of alignment, you can try realigning it by tapping on the bolt handle with a soft hammer. If the bolt is seized, you may need to take the rifle to a gunsmith for repair.

How do I put the bolt back in a Remington 700?

1. Ensure that the rifle is unloaded and the safety is engaged.
2. Insert the bolt into the receiver, making sure that the bolt lugs are aligned with the receiver lugs.
3. Press down on the bolt release button and push the bolt forward until it is fully seated in the receiver.

What are the common mistakes people make when removing the bolt from a Remington 700?

There are a few common mistakes people make when removing the bolt from a Remington 700.

• Not disengaging the safety. If the safety is engaged, the bolt cannot be removed from the rifle.
• Not depressing the bolt release button. The bolt release button must be depressed in order to release the bolt from the rifle.
• Pulling the bolt handle too far. The bolt handle should only be pulled back far enough to release the bolt from the rifle. Pulling the bolt handle too far can damage the bolt or the rifle.

What are the safety precautions I should take when removing the bolt from a Remington 700?

When removing the bolt from a Remington 700, it is important to take the following safety precautions:

• Ensure that the rifle is unloaded and the safety is engaged.
• Never point the rifle at anything you do not intend to shoot.
• Keep your finger off the trigger until you are ready to fire.
• Be aware of your surroundings and the potential for ricochets.

Where can I find more information on removing the bolt from a Remington 700?

For more information on removing the bolt from a Remington 700, you can consult the following resources:

• The Remington 700 Owner’s Manual
• The Remington 700 website
• Online forums and discussion boards
• Gunsmithing shops

  In this blog post, we have discussed how to remove a bolt from a Remington 700. We started by identifying the parts of the bolt and the tools needed for the job. Then, we walked you through the steps of removing the bolt, step-by-step. Finally, we provided some tips for troubleshooting common problems.

We hope that this blog post has been helpful. If you have any questions, please feel free to leave them in the comments section below.