How To Clean A Glock 43?

How to Clean a Glock 43

The Glock 43 is a popular concealed carry weapon, and it’s important to know how to clean it properly to keep it in good working order. Cleaning your Glock 43 is a relatively simple process, but it’s important to do it correctly to avoid damaging the gun.

In this article, we’ll walk you through the steps of cleaning a Glock 43, from disassembling the gun to putting it back together. We’ll also provide some tips on how to keep your Glock 43 clean and well-maintained.

So whether you’re a new Glock owner or you’re just looking for a refresher on how to clean your gun, read on for all the information you need.

Step	Instructions	Image
1	Remove the slide from the frame.
2	Disassemble the slide.
3	Clean the slide with a brush and solvent.
4	Reassemble the slide.
5	Clean the frame with a brush and solvent.
6	Lubricate the frame and slide.

How to Clean a Glock 43?

This guide will show you how to clean your Glock 43 pistol safely and effectively. It includes detailed instructions for disassembly, assembly, and cleaning the internal and external components of the gun.

Safety Precautions

Before you begin cleaning your Glock 43, it is important to take some safety precautions.

• Make sure the gun is unloaded. This means removing the magazine and checking the chamber to ensure that there is no round in the gun.
• Clear the gun’s firing pin safety. The Glock 43 has a firing pin safety that prevents the gun from firing unless the trigger is pulled. To clear the firing pin safety, pull the trigger to the rear and hold it there.
• Place the gun on a table or other stable surface. This will prevent the gun from slipping and falling while you are cleaning it.
• Wear eye protection. This will protect your eyes from any flying debris that may be created during the cleaning process.

Disassembly and Assembly

To disassemble your Glock 43, follow these steps:

1. Remove the magazine from the gun.
2. Depress the slide lock lever and pull the slide back until it is fully open.
3. Use a small tool to push the takedown lever down.
4. While holding the takedown lever down, release the slide and allow it to move forward.
5. The slide and barrel will now be separated from the frame.

To reassemble your Glock 43, follow these steps:

1. Insert the slide into the frame.
2. Push the takedown lever up until it engages with the slide.
3. Move the slide forward until it is fully closed.
4. Release the slide lock lever.
5. Insert the magazine into the gun.

Cleaning the Internal Components

To clean the internal components of your Glock 43, you will need the following tools and materials:

• A cleaning brush
• A cleaning solvent
• A rag
• A gun oil

1. Remove the slide and barrel from the frame.
2. Spray the cleaning solvent on the slide and barrel.
3. Use the cleaning brush to scrub the slide and barrel until they are clean.
4. Wipe the slide and barrel with a rag to remove any remaining solvent.
5. Apply a small amount of gun oil to the slide and barrel.
6. Reassemble the Glock 43.

Cleaning the External Components

To clean the external components of your Glock 43, you will need the following tools and materials:

• A cleaning cloth
• A gun oil

1. Wipe the exterior of the gun with a cleaning cloth.
2. Apply a small amount of gun oil to the exterior of the gun.
3. Buff the gun with a clean cloth to remove any excess oil.

By following these steps, you can clean your Glock 43 pistol safely and effectively. This will help to keep your gun in good working order and prevent it from becoming damaged.

Here are some additional tips for cleaning your Glock 43:

• Clean your gun regularly, especially if you have been shooting it frequently.
• Store your gun in a clean, dry place.
• Avoid exposing your gun to extreme temperatures.
• If your gun becomes dirty or damaged, take it to a qualified gunsmith for cleaning and repair.

By following these tips, you can keep your Glock 43 in good condition for many years to come.

Cleaning the Slide and Barrel

The slide and barrel of your Glock 43 are two of the most important parts of the gun, and they need to be kept clean and lubricated in order to function properly. Here are the steps on how to clean the slide and barrel of your Glock 43:

1. Remove the slide from the frame.
2. Remove the barrel from the slide.
3. Clean the slide rails with a cleaning rod and solvent.
4. Clean the inside of the slide with a cleaning brush and solvent.
5. Clean the barrel with a cleaning rod and solvent.
6. Lubricate the slide rails and the inside of the slide.
7. Lubricate the barrel.
8. Reassemble the slide and barrel.

Here are some tips for cleaning the slide and barrel of your Glock 43:

• Use a cleaning rod that is the same diameter as the barrel.
• Use a cleaning brush that is soft enough to not damage the finish of the slide and barrel.
• Use a solvent that is specifically designed for cleaning firearms.
• Lubricate the slide rails and the inside of the slide with a light coat of oil.
• Lubricate the barrel with a light coat of grease.

By following these steps, you can keep the slide and barrel of your Glock 43 clean and lubricated, which will help to ensure that it functions properly and lasts for many years to come.

Lubrication

Lubricating your Glock 43 is an important part of maintaining it properly. Lubrication helps to reduce friction between moving parts, which can help to improve the performance of your gun and extend its lifespan.

There are a few different types of lubricants that you can use on your Glock 43. The type of lubricant that you use will depend on the climate where you live. In general, a light oil is a good choice for Glocks that are used in warm climates, while a heavier grease is a good choice for Glocks that are used in cold climates.

Here are some tips for lubricating your Glock 43:

• Use a lubricant that is specifically designed for firearms.
• Apply a thin coat of lubricant to the moving parts of your gun.
• Do not over-lubricate your gun, as this can actually cause problems.
• Reapply lubricant as needed.

By following these tips, you can keep your Glock 43 properly lubricated and ensure that it functions properly.

Cleaning and lubricating your Glock 43 is an important part of maintaining it properly. By following the steps in this guide, you can keep your gun clean and lubricated, which will help to ensure that it functions properly and lasts for many years to come.

How often should I clean my Glock 43?

A: Glocks are designed to be self-cleaning, but it is still a good idea to clean them regularly. A good rule of thumb is to clean your Glock 43 after every 500 rounds fired.

What do I need to clean my Glock 43?

A: You will need the following items to clean your Glock 43:

• A cleaning kit specifically designed for Glocks
• A solvent, such as Hoppe’s No. 9 or Break-Free CLP
• A lubricant, such as Gun Oil or Slip 2000 EWL
• A rag or paper towels
• A toothbrush
• A bore brush
• A cleaning rod

How do I clean the exterior of my Glock 43?

A: To clean the exterior of your Glock 43, follow these steps:

1. Remove the magazine and the slide from the frame.
2. Use a rag or paper towels to wipe down the exterior of the frame and slide.
3. Use a toothbrush to clean the serrations on the slide.
4. Use a bore brush to clean the inside of the barrel.
5. Apply a light coat of lubricant to the exterior of the frame and slide.

How do I clean the interior of my Glock 43?

A: To clean the interior of your Glock 43, follow these steps:

1. Remove the magazine and the slide from the frame.
2. Disassemble the slide by removing the two takedown pins.
3. Use a solvent to clean the inside of the slide.
4. Use a toothbrush to clean the small parts of the slide.
5. Use a bore brush to clean the inside of the barrel.
6. Reassemble the slide.
7. Clean the inside of the frame with a solvent.
8. Use a toothbrush to clean the small parts of the frame.
9. Apply a light coat of lubricant to the inside of the frame.

What are some common problems with Glock 43s?

A: Some common problems with Glock 43s include:

• Failure to eject
• Failure to feed
• Trigger pull is too heavy
• Magazine release is too stiff

How can I fix common problems with my Glock 43?

A: If you are experiencing problems with your Glock 43, you can try the following solutions:

• Clean the gun thoroughly.
• Check the ammunition you are using.
• Adjust the trigger pull.
• Lubricate the gun.

If you are unable to fix the problem yourself, you can take your Glock 43 to a qualified gunsmith.

cleaning your Glock 43 is an important part of maintaining its performance and safety. By following the steps outlined in this guide, you can ensure that your Glock 43 is clean and well- lubricated, and that it will function properly for many years to come.

Here are some key takeaways from this guide:

• Use a soft, lint-free cloth to clean the exterior of your Glock 43.
• Use a cleaning rod and solvent to clean the barrel and slide.
• Use a toothbrush and solvent to clean the internal parts of your Glock 43.
• Apply a light coat of lubricant to all moving parts of your Glock 43.
• Be sure to dry your Glock 43 completely before storing it.

By following these simple steps, you can keep your Glock 43 in top condition and ensure that it is always ready to use when you need it.