How to Disassemble a Remington 870 for Cleaning and Maintenance

How to Take Apart a Remington 870

The Remington 870 is a popular pump-action shotgun that is known for its reliability and durability. It is a versatile firearm that can be used for hunting, home defense, and competition shooting. While the 870 is a relatively simple gun to operate, it is still important to know how to take it apart for cleaning and maintenance.

This guide will walk you through the process of disassembling and reassembling a Remington 870. It is important to note that this guide is not intended to replace the owner’s manual for your specific firearm. Always consult your owner’s manual for specific instructions and safety information.

With that said, let’s get started!

Step	Instructions	Image
1	Remove the magazine tube cap.
2	Push the bolt release button down and pull the bolt back to the rear of the receiver.
3	Grasp the front of the bolt and pull it out of the receiver.
4	Remove the fore-end cap.
5	Rotate the fore-end assembly 90 degrees counterclockwise and pull it forward off of the receiver.
6	Remove the barrel assembly from the receiver.

Step 1: Remove the magazine tube

To remove the magazine tube from a Remington 870, you will need to:

1. Open the action of the shotgun by pulling back on the slide and locking it open.
2. Locate the magazine tube cap at the front of the receiver.
3. Use a screwdriver to pry up the magazine tube cap.
4. Remove the magazine tube cap and spring.
5. Pull the magazine tube out of the receiver.

Step 2: Remove the bolt assembly

To remove the bolt assembly from a Remington 870, you will need to:

1. Open the action of the shotgun by pulling back on the slide and locking it open.
2. Locate the bolt release button on the left side of the receiver.
3. Press the bolt release button and pull the bolt assembly out of the receiver.

Once the bolt assembly is removed, you can clean and lubricate the shotgun. To reassemble the shotgun, simply reverse the steps above.

Additional Tips

• When removing the magazine tube cap, be careful not to damage the spring.
• When removing the bolt assembly, be careful not to lose the firing pin retainer spring.
• When cleaning the shotgun, be sure to use a solvent that is safe for firearms.
• When lubricating the shotgun, use a light coat of oil.

By following these steps, you can safely and easily remove the magazine tube and bolt assembly from a Remington 870. This will allow you to clean and lubricate the shotgun, as well as troubleshoot any problems that may arise.

Step 3: Remove the barrel.

1. With the Remington 870 held in your dominant hand, use your non-dominant hand to hold the barrel in place.
2. Using a screwdriver, turn the barrel lock screw counterclockwise until it is loose.
3. Remove the barrel lock screw and set it aside.
4. Pull the barrel forward and off of the receiver.

Step 4: Clean and lubricate the Remington 870

1. Remove the magazine from the Remington 870.
2. Use a cleaning rod and solvent to clean the bore of the barrel.
3. Use a brush to clean the action of the Remington 870.
4. Apply a light coat of oil to the moving parts of the Remington 870.
5. Reassemble the Remington 870.

By following these steps, you can safely and effectively take apart and clean your Remington 870. This will help to ensure that your shotgun is functioning properly and that it is safe to use.

Here are some additional tips for cleaning and maintaining your Remington 870:

• Clean the Remington 870 after each use.
• Store the Remington 870 in a dry place.
• Avoid exposing the Remington 870 to extreme temperatures.
• Use only high-quality cleaning products and lubricants.

By following these tips, you can help to extend the life of your Remington 870 and ensure that it is always ready to use.

How To Take Apart A Remington 870?

Q: What tools do I need to take apart a Remington 870?

A: You will need the following tools:

• A flathead screwdriver
• A Phillips head screwdriver
• A cleaning rod
• A set of Allen wrenches

Q: How do I take apart the action assembly?

A: To take apart the action assembly, follow these steps:

1. Remove the magazine tube cap by unscrewing it counterclockwise.
2. Remove the magazine spring and follower by pulling them out of the magazine tube.
3. Remove the bolt assembly by pulling it back and out of the receiver.
4. Remove the bolt head by unscrewing it counterclockwise.
5. Remove the bolt carrier by pulling it out of the receiver.

Q: How do I take apart the barrel assembly?

A: To take apart the barrel assembly, follow these steps:

1. Remove the barrel from the receiver by unscrewing the barrel nut counterclockwise.
2. Remove the gas tube by unscrewing it counterclockwise.
3. Remove the front sight assembly by unscrewing it counterclockwise.

Q: How do I put the Remington 870 back together?

A: To put the Remington 870 back together, follow these steps:

1. Put the barrel assembly back together in the reverse order of how you took it apart.
2. Put the action assembly back together in the reverse order of how you took it apart.
3. Insert the magazine tube spring and follower into the magazine tube.
4. Screw the magazine tube cap onto the magazine tube.

Additional tips for taking apart a Remington 870:

• Be careful not to lose any small parts.
• Keep track of the order in which you remove the parts so that you can put them back together correctly.
• If you are having trouble, consult the owner’s manual or a qualified gunsmith.

  In this comprehensive guide, we have discussed how to take apart a Remington 870 shotgun. We started by discussing the tools and materials you will need. We then provided step-by-step instructions on how to disassemble the shotgun, starting with the barrel and working our way down to the action. We also provided some tips and tricks to help you along the way.

We hope that this guide has been helpful and that you now feel confident in your ability to disassemble and reassemble your Remington 870 shotgun. As always, please be careful when working with firearms and follow all safety precautions.