How To Disassemble Ruger 10 22?

How to Disassemble a Ruger 10/22

The Ruger 10/22 is a popular .22 caliber rifle that is known for its reliability and accuracy. It is also relatively easy to disassemble for cleaning and maintenance. In this article, we will walk you through the process of disassembling a Ruger 10/22 in a few simple steps.

Before you begin, make sure that the rifle is unloaded and that the safety is engaged.

1. Remove the magazine from the rifle.
2. Press down on the front of the trigger guard and pull back on the bolt handle to open the action.
3. Rotate the takedown lever 90 degrees clockwise.
4. Pull the bolt assembly forward and out of the receiver.
5. Remove the barrel from the receiver.
6. Reassemble the rifle in the reverse order.

Step	Instructions	Image
1	Remove the magazine.
2	Depress the bolt release and pull the bolt back to its full rearward position.
3	Rotate the takedown lever 90 degrees clockwise.
4	Grasp the front and rear of the receiver and pull them apart.

Tools Needed

To disassemble a Ruger 10/22, you will need the following tools:

• A flat-head screwdriver
• A small punch
• A cleaning rod
• A few drops of gun oil

Disassembling the Action

1. Remove the magazine from the rifle.
2. Lock the bolt to the rear by pulling back on the bolt handle and depressing the bolt release button.
3. Remove the bolt by pulling it straight back out of the receiver.
4. Rotate the rear takedown pin 90 degrees clockwise and remove it from the rifle.
5. Move the front takedown pin forward until it is flush with the receiver.
6. Use a punch to push out the front takedown pin.
7. The action is now disassembled.

To reassemble the action, follow these steps in reverse order.

Additional Tips

• Be careful not to lose any small parts when disassembling the rifle.
• Keep the parts clean and lubricated to prevent rust and corrosion.
• If you are unsure how to disassemble the rifle, consult the owner’s manual or a qualified gunsmith.

Disassembling the Bolt

To disassemble the bolt, follow these steps:

1. Remove the magazine from the rifle.
2. Depress the bolt release button and pull the bolt back to the rear of the receiver.
3. Hold the bolt release button down and rotate the bolt handle counterclockwise until it stops.
4. Remove the bolt from the receiver.

Disassembling the Trigger Assembly

To disassemble the trigger assembly, follow these steps:

1. Remove the magazine from the rifle.
2. Depress the trigger and pull the bolt back to the rear of the receiver.
3. Using a small screwdriver, pry the trigger guard up and off of the receiver.
4. Remove the trigger spring and trigger assembly from the receiver.

Disassembling the Barrel

To disassemble the barrel, follow these steps:

1. Remove the magazine from the rifle.
2. Depress the bolt release button and pull the bolt back to the rear of the receiver.
3. Remove the barrel nut from the barrel.
4. Remove the barrel from the receiver.

Reassembling the Ruger 10 22

To reassemble the Ruger 10 22, follow these steps:

1. Assemble the barrel to the receiver.
2. Install the barrel nut and tighten it to 30 ft-lbs of torque.
3. Assemble the trigger assembly to the receiver.
4. Install the trigger guard.
5. Insert the bolt into the receiver and rotate the bolt handle clockwise until it stops.
6. Depress the bolt release button and release the bolt.
7. Insert a magazine into the rifle.

Disassembling and reassembling the Ruger 10 22 is a relatively simple process. By following these steps, you can safely and easily maintain your rifle.

Here are some additional tips for disassembling and reassembling the Ruger 10 22:

• Use a clean cloth or rag to wipe down the parts of the rifle before and after disassembly.
• Lubricate the parts of the rifle with a light coat of oil before reassembly.
• Be careful not to lose any small parts during disassembly.
• If you are unsure of how to disassemble or reassemble the rifle, consult the owner’s manual.

  How do I disassemble a Ruger 10/22?

1. Remove the magazine.
2. Lock the bolt back.
3. Depress the takedown button located at the front of the trigger guard.
4. While depressing the takedown button, rotate the rear of the receiver down and away from the barrel.
5. The receiver and barrel can now be separated.

What tools do I need to disassemble a Ruger 10/22?

You will need a small flathead screwdriver to remove the magazine catch and a small punch to depress the takedown button.

Can I disassemble a Ruger 10/22 without tools?

It is possible to disassemble a Ruger 10/22 without tools, but it is not recommended. Using tools will make the process easier and less likely to damage the rifle.

What should I do if I get stuck while disassembling my Ruger 10/22?

If you get stuck while disassembling your Ruger 10/22, stop and consult the owner’s manual. You can also contact Ruger customer service for assistance.

Is it safe to disassemble a Ruger 10/22?

Yes, it is safe to disassemble a Ruger 10/22 as long as you follow the proper steps. Be sure to keep the rifle pointed in a safe direction and remove the magazine before beginning.

What are the benefits of disassembling a Ruger 10/22?

There are several benefits to disassembling a Ruger 10/22, including:

• Cleaning and maintenance: Disassembling the rifle allows you to clean and lubricate it more thoroughly.
• Repairs: If your rifle is not functioning properly, you may be able to identify and fix the problem by disassembling it.
• Modifications: You can also modify your rifle by disassembling it and adding new parts.

What are the risks of disassembling a Ruger 10/22?

There are a few risks associated with disassembling a Ruger 10/22, including:

• Damage to the rifle: If you are not careful, you could damage the rifle by disassembling it incorrectly.
• Injury: If you are not careful, you could injure yourself by disassembling the rifle.

How often should I disassemble my Ruger 10/22?

The frequency with which you should disassemble your Ruger 10/22 depends on how often you use it. If you shoot your rifle regularly, you should disassemble it and clean it every few hundred rounds. If you do not shoot your rifle very often, you can disassemble it and clean it less frequently.

In this article, we have discussed how to disassemble a Ruger 10/22. We started by explaining the different parts of the rifle and how they work together. Then, we walked you through the steps of disassembly, making sure to point out any important safety considerations. Finally, we put the rifle back together and gave you some tips for cleaning and maintenance.

We hope that this article has been helpful and that you now feel confident in your ability to disassemble and reassemble your Ruger 10/22. If you have any questions, please do not hesitate to contact us.

Here are some key takeaways from this article:

• The Ruger 10/22 is a popular semi-automatic rifle that is easy to disassemble and reassemble.
• The different parts of the rifle are: the receiver, barrel, bolt, trigger assembly, and magazine.
• To disassemble the rifle, you will need to remove the magazine, take down the bolt, and unscrew the stock.
• To reassemble the rifle, you will need to reverse the disassembly steps.
• Be sure to follow all safety precautions when disassembling and assembling your rifle.